anastill.blogg.se

Cisco 2950 switch layer 3
Cisco 2950 switch layer 3




cisco 2950 switch layer 3
  1. Cisco 2950 switch layer 3 how to#
  2. Cisco 2950 switch layer 3 software#
  3. Cisco 2950 switch layer 3 windows#

The information in this document was created from the devices in a specific lab environment. Note: Cisco does not recommend any Wake-On-LAN utility.

Cisco 2950 switch layer 3 windows#

PCs that run Microsoft Windows 2000 operating systemįreeware Wake-On-LAN utility from SolarWinds

Cisco 2950 switch layer 3 software#

The information in this document is based on these software and hardware versions:Ĭatalyst 3750 Series Switch that runs Cisco IOS® system Software Release 12.2(25r)SECĬatalyst 2950 Series Switches that run Cisco IOS system Software Release 12.1(19)EA1a Understanding and Troubleshooting DHCP in Catalyst Switch or Enterprise Networks Using PortFast and Other Commands to Fix Workstation Startup Connectivity Delays

cisco 2950 switch layer 3

Cisco 2950 switch layer 3 how to#

How To Configure InterVLAN Routing on Layer 3 Switches Prerequisites RequirementsĬisco recommends that you have knowledge of these topics before you attempt this configuration:Ĭreating Ethernet VLANs on Catalyst Switches Hardware is Fast Ethernet, address is 000d.2908.0b57 (bia document provides a sample configuration for Wake-On-LAN (WOL) support across VLANs with a Catalyst Layer 3 switch. Input queue: 0/75/0/0 (size/max/drops/flushes) Total output drops: 0ĥ minute input rate 0 bits/sec, 0 packets/secĥ minute output rate 7000 bits/sec, 9 packets/secĤ1034 packets input, 3091158 bytes, 0 no bufferĠ input errors, 0 CRC, 0 frame, 0 overrun, 0 ignoredĠ watchdog, 1223 multicast, 0 pause inputĠ input packets with dribble condition detectedĥ99493 packets output, 59236405 bytes, 0 underrunsĠ output errors, 0 collisions, 2 interface resetsĠ lost carrier, 0 no carrier, 0 PAUSE outputĠ output buffer failures, 0 output buffers swapped outįastEthernet0/23 is up, line protocol is up (connected) Last clearing of “show interface” counters never

cisco 2950 switch layer 3

Input flow-control is unsupported output flow-control is unsupported Port Vlans in spanning tree forwarding state and not prunedįastEthernet0/24 is up, line protocol is up (connected) Port Vlans allowed and active in management domain Port Mode Encapsulation Status Native vlan Typically the command is interface fastethernet 1/0 which then puts in in config mode for that interface. Notice these switch interfaces commands from the example: Note: what’s probably happening is that the switchports are in dynamic mode so you can’t make a dynamic port a trunk port.Ĭonfig# int fastethernet 0/X/X Ĭonfig-int# switchport trunk encapsulation dot1qĬheck your config using the sh run to list each port and how they are configured. (config-if)# switchport trunk encapsulation dot1q (config-if)# description trunk-to-router-on-a-stick Next: from the example:(config)# interface FastEthernet1/0/1 Now, in order for the two hosts to communicate between them, they must set as default gateway the IP address of the corresponding router subinterface address (e.g for host in VLAN 10 the gateway must be 10.10.10.2 and for host in VLAN 20 the gateway must be 20.20.20.2). Note: from the router on a stick example: Did you configure subinterfaces on your 2801?






Cisco 2950 switch layer 3